DL26 19" 2U Сhassis 530mm DEEP

Form Factor 2U chassis supports for micro-ATX size (244x244mm) motherboard Dimensions(mm) Height: 88mm Width: 483mm Depth: 530mm Net weight: 7.8kg Expansion slots - 4x Low Profile PCI expansion slot Drive Bays - 12x 3.5"HDD bay Front Panel LEDs: - Hard drive activity - Power - Alarm Buttons: - Reset - Power Detailed description System Cooling - 4x 80x80x25 2800RPM fans, 3.72m3 total controlled by intelligent cooling system FanMagic® - 1x 80x80 PSU fan Operating Environment (System) Operating Temperature Range: +5~50º Power Supply PSU 400W 460W 550W 600W Input Voltage 220VAC  100~ 240VAC  100~ 240VAC  100~ 240VAC  +3.3V 30A 27A 27A 36A +5V 28A 29A 29A 30A +5V standby 2A 2A 2A 2A -5V 0.3A 0.3A 0.3A - +12V1 +12V2 +12V3,+12V4 18A - - 16.5A 15A - 18A 18A - 15A 15A 15A -12V 0.8A 0.5A 0.5A 0.5A Mounting in rack - Slide Rail Kit DR-2U-400 supplies with chassis, look at application notes Package Height: 125mm Width: 510mm Depth: 600mm Gross weight: 10.8kg (8.8kg w/o PSU) Available Colors  RAL7032 Beige     RAL9005 Black Ordering Information Part number Description Chassis color DL26xxx-W DL26xxx-B White(Beige) Black Power Supply DL26400 DL26460 DL26550 DL26600 400W 460W 550W 600W Optional Parts List Model Description Low Profile PCI brackets - more>> Air filter F80 more>> Cable-adapter 2 x HDD power SATA Power 2хSATA_L Cable-adapter 2 x HDD power 330mm length. more>> Cable-adapter 3 x HDD power SATA Power 3хSATA IDC Cable-adapter 3 x HDD power 330mm length. more>> Power Connector HDD SATA Power SATA Connector HDD SATA power connector. Just crimp it to wires yourself. more>> Back panel drawing with installed I/O cards Technical drawing Documentation: Chassis Quick Reference  | Safety instruction

PHOTOGALLERY
click to view large picture

You can install up to 12 HDD(3,5") in chassis without additional equipment.

The DR-2U-400 Slide Rail Kit to mount chassis to 19" wall mounted cabinet/frame consists of two symmetric Holders - left and right. Each Holder consists of two parts - Front Bracket (1) and Back Bracket (2). Slide together the front to back sections of the Holders as shown on the picture on the left. Extend the Holders to the length required to fit the rack or cabinet before you install it. The DR-2U-400 Kit supports rack fixing distance on depth L from 243mm to 540mm. Notify, there are two variants to join Back Bracket (A and B). Screw on appropriate nuts (3) (supplied with the Kit) to each bracket, and tighten the front and the back sections.

Install 10 cage nuts in the rack (not supplied with the Kit). Refer to the picture on the left. You should install 5 cage nuts (red marked): 3 - on the front rack (1) and 2 - on the back rack of the frame. Tighten the both Holders with 4 appropriate screws for EACH SIDE of the rack (left and right, front and back). You need to tighten 8 screws total.
Note! Please make sure the salient side of each Holder (left and right) is in the opposite position in the rackmount.

Slide the DL26 based system along the pre-installed Holders in the suitable rack. Tighten the rest 2 screws on the opposite side of the front panel where it attaches to the rack.

For additional information refer to the page of frames accessories >>>